Arduino - MKR1000BatteryLife

MKR1000 Battery Life

This tutorial gives an overview on how to determine the duration of a recharegeable battery connected to an Arduino MKR1000. Using a simple formula, it is possible to calculate how long a charge can last. The duration is related to the current drawn by the board under different conditions that depend on the sketch and the hardware functionalities used. In this example we use a LiPo battery rated at 1400mAh.

Hardware Required

  • Arduino MKR1000 Board

  • 1400mAh LiPo battery

The Circuit

Battery connected to the board through the on-board JST connector

ArduinoMKR1000Battery bb


The charging circuit on the MKR1000 board has a charge current fixed at 350mA and a standby charge time of 4 hours. LiPo battieries should not be charged with a current higher than a half of the total capacity. MKR1000 is therefore designed to use batteries with 'at least 700mAh' of capacity. The maximum capacity is not critical, but bigger batteries require more time to fully charge, therefore we suggest a maximum of 1400-1500mAh.

Computing Battery Life

Computing how long a battery can last is generally speaking quite simple. Each rechargeable battery has its capacity printed on its package, expressed in mAh. This value means that the battery is able to provide the current stated for one hour and after that it will be depleted. If we draw less current, the battery will take more time to discharge. If we know the average current consumption of our circuit we can compute the battery life, expressed in hour using the following formula:

Battery Life = (Battery Capacity) / (Average Current Consumption) * 0.7

If we want the worst case for battery life duration, we can use the maximum current absorbed by our circuit instead of the average one:

Battery Life = (Battery Capability) / (Maximum Current Consumption) * 0.7


Please note that the factor of 0.7 makes allowances for external factors which can affect battery life for out of specs usage (deep discharge under suggested voltage, mechanical stress etc).

MKR1000 current consumption

The main feature of the MKR1000 board that affects battery life is the WiFi connectivity: it absorbs roughly 100mA when connected to an Access Point and data transfers are on-going. If the WiFi module is not initialized, it is automatically set into low power mode. The consumption of the micro-controller is about 20mA. A sketch using WiFi connection has therefore an average current absorption of 120mA. If we run this information in our formula we get:

Application Run Time = Battery Life = (1400mAh) / (120mA) * 0.7 = 8.16h

This estimate has been made running the sketch listed below.


  Repeating WiFi Web Client

 This sketch connects to a a web server and makes a request

 using an Arduino WiFi shield.


 * WiFi shield attached to pins SPI pins and pin 7

 created 23 April 2012

 modified 31 May 2012

 by Tom Igoe

 modified 13 Jan 2014

 by Federico Vanzati

 This code is in the public domain.


#include <SPI.h>
#include <WiFi101.h>

#include "arduino_secrets.h"
///////please enter your sensitive data in the Secret tab/arduino_secrets.h
char ssid[] = SECRET_SSID;        // your network SSID (name)
char pass[] = SECRET_PASS;    // your network password (use for WPA, or use as key for WEP)
int keyIndex = 0;            // your network key Index number (needed only for WEP)

int status = WL_IDLE_STATUS;

// Initialize the WiFi client library

WiFiClient client;

// server address:
char server[] = "";
//IPAddress server(64,131,82,241);

unsigned long lastConnectionTime = 0;            // last time you connected to the server, in milliseconds

const unsigned long postingInterval = 10L * 1000L; // delay between updates, in milliseconds

void setup() {

  //Initialize serial and wait for port to open:


  while (!Serial) {

    ; // wait for serial port to connect. Needed for native USB port only


  // check for the presence of the shield:

  if (WiFi.status() == WL_NO_SHIELD) {

    Serial.println("WiFi shield not present");

    // don't continue:

    while (true);


  // attempt to connect to WiFi network:

  while ( status != WL_CONNECTED) {

    Serial.print("Attempting to connect to SSID: ");


    // Connect to WPA/WPA2 network. Change this line if using open or WEP network:

    status = WiFi.begin(ssid, pass);

    // wait 10 seconds for connection:



  // you're connected now, so print out the status:


void loop() {

  // if there's incoming data from the net connection.

  // send it out the serial port.  This is for debugging

  // purposes only:

  while (client.available()) {

    char c =;



  // if ten seconds have passed since your last connection,

  // then connect again and send data:

  if (millis() - lastConnectionTime > postingInterval) {




// this method makes a HTTP connection to the server:
void httpRequest() {

  // close any connection before send a new request.

  // This will free the socket on the WiFi shield


  // if there's a successful connection:

  if (client.connect(server, 80)) {


    // send the HTTP PUT request:

    client.println("GET / HTTP/1.1");


    client.println("User-Agent: ArduinoWiFi/1.1");

    client.println("Connection: close");


    // note the time that the connection was made:

    lastConnectionTime = millis();


  else {

    // if you couldn't make a connection:

    Serial.println("connection failed");


void printWiFiStatus() {

  // print the SSID of the network you're attached to:

  Serial.print("SSID: ");


  // print your WiFi shield's IP address:

  IPAddress ip = WiFi.localIP();

  Serial.print("IP Address: ");


  // print the received signal strength:

  long rssi = WiFi.RSSI();

  Serial.print("signal strength (RSSI):");


  Serial.println(" dBm");

Computing your application average current consumption

The fastest way to compute your application current consumption is by means of an ammeter. To do this you can use the following circuit.

ArduinoMKR1000Ammeter bb

Once you have the ammeter reading you can easily use the formula we used before.